|
|
Hi Paul,
In my last conversation with Bruce he said he was getting the getting
the manifold flanges water jet cut. He's geting set up for all the
variations including the Renessis. I think the manifold in the photo
will look a little rough compared to his next version.
Bob White
On Tue, 21 Dec 2004 19:12:37 -0600
"Paul" <sqpilot@bellsouth.net> wrote:
Thanks for the info and the picture, Bob....Very similar to my Atkins
setup, although Bruce's looks more refined....I suspect his intake
better matches the ports. I hope you are pleased with it when you
receive it. Bruce has a pretty good reputation for his engines, I
suspect that will flow over onto his manifolds. Paul Conner
----- Original Message ----- From: "Bob White" <bob@bob-white.com>
To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
Sent: Tuesday, December 21, 2004 9:12 AM
Subject: [FlyRotary] Re: East Coast Rotary Intake
> Hi Paul,
>
> It's a straight out design. Here is a photo of the first one Bruce
> made. I think it was sent to Denmark. There are some supports not
> shown. Bruce reports that it weighs 6.5 lbs with runner lengths of
> 7 inches. I have also asked Bruce to put the throttle body on the
> other end so I can get some ram air into it.
>
> Bob White (still waiting...maybe next week!)
>
>
> On Mon, 20 Dec 2004 21:52:14 -0600
> "Paul" <sqpilot@bellsouth.net> wrote:
>
>> Hi, Bob....just deleting some older e-mails and came across yours
>> again.... Can you provide any details about Bruce's intake
>manifold? > Wrap over the top or straight out, provisions for
>injectors, etc? > Thanks in advance for your reply. Paul Conner
>>
>> ----- Original Message ----- >> From: "Bob White" <bob@bob-white.com>
>> To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
>> Sent: Wednesday, December 08, 2004 7:17 PM
>> Subject: [FlyRotary] Re: East Coast Rotary Intake
>>
>>
>> > Hi Dana,
>> >
>> > Bruce has been building one for me for a couple of months. It's
>> > going kind of slow because he does it between engine work, and
>he's > > making all the dies so that he can go into production. I'm
>not > > quite read for it yet so I haven't pushed very hard. Last I
>heard > > he will be ready to ship it next week. (Maybe :-)
>> >
>> > Bob White
>> >
>> > On Wed, 08 Dec 2004 19:13:22 -0500
>> > "Dana Overall" <bo124rs@hotmail.com> wrote:
>> >
>> >> Any word on Bruce's prefab intake out there to be had??
>> >>
>> >>
>> >>
>> >> Dana Overall
>> >> Richmond, KY i39
>> >> RV-7 slider, Imron black, "Black Magic"
>> >> Finish kit
>> >> 13B Rotary. Hangar flying my Dynon.
>> >> http://rvflying.tripod.com
>> >> http://rvflying.tripod.com/blackrudder.jpg
>> >> do not archive
>> >>
>> >>
>> >>
>> >> >> Homepage: http://www.flyrotary.com/
>> >> >> Archive: >http://lancaironline.net/lists/flyrotary/List.html > >>
>> >>
>> >
>> >
>> > -- >> > http://www.bob-white.com
>> > N93BD - Rotary Powered BD-4 (soon)
>> >
>> >>> Homepage: http://www.flyrotary.com/
>> >>> Archive: http://lancaironline.net/lists/flyrotary/List.html
>> >
>>
>>
>>
>>
>> -- >> No virus found in this outgoing message.
>> Checked by AVG Anti-Virus.
>> Version: 7.0.296 / Virus Database: 265.6.2 - Release Date:
>12/20/2004 >
>>
>> >> Homepage: http://www.flyrotary.com/
>> >> Archive: http://lancaironline.net/lists/flyrotary/List.html
>>
>>
>
>
> -- > http://www.bob-white.com
> N93BD - Rotary Powered BD-4 (soon)
>
---------------------------------------------------------------------
-----------
>>> Homepage: http://www.flyrotary.com/
>>> Archive: http://lancaironline.net/lists/flyrotary/List.html
>
---------------------------------------------------------------------
-----------
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.296 / Virus Database: 265.6.3 - Release Date: 12/21/2004
-- No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.296 / Virus Database: 265.6.3 - Release Date: 12/21/2004
>> Homepage: http://www.flyrotary.com/
>> Archive: http://lancaironline.net/lists/flyrotary/List.html
--
http://www.bob-white.com
N93BD - Rotary Powered BD-4 (soon)
|
|