X-Virus-Scanned: clean according to Sophos on Logan.com Return-Path: Received: from gluon.sasknet.sk.ca ([142.165.20.181] verified) by logan.com (CommuniGate Pro SMTP 5.4c3j) with ESMTPS id 4954507 for flyrotary@lancaironline.net; Fri, 22 Apr 2011 14:35:36 -0400 Received-SPF: none receiver=logan.com; client-ip=142.165.20.181; envelope-from=hjjohnson@sasktel.net Received: from pps.filterd (gluon [127.0.0.1]) by gluon.sasknet.sk.ca (8.14.3/8.14.3) with SMTP id p3MIXMjh029562 for ; Fri, 22 Apr 2011 12:34:59 -0600 Received: from bgmpomr1.sasknet.sk.ca (bgmpOMR1.sasknet.sk.ca [142.165.72.22]) by gluon.sasknet.sk.ca with ESMTP id vud7fuksy-1 for ; Fri, 22 Apr 2011 12:34:59 -0600 Received: from sasktel.net ([192.168.234.97]) by bgmpomr1.sasknet.sk.ca (SaskTel eMessaging Service) with ESMTP id <0LK200MW7GYB83R0@bgmpomr1.sasknet.sk.ca> for flyrotary@lancaironline.net; Fri, 22 Apr 2011 12:34:59 -0600 (CST) Received: from [192.168.234.24] (Forwarded-For: [216.197.211.104]) by cgmail1.sasknet.sk.ca (mshttpd); Fri, 22 Apr 2011 12:34:59 -0600 Date: Fri, 22 Apr 2011 12:34:59 -0600 From: H & J Johnson Subject: Re: [FlyRotary] Re: Mistral 'Like' Intake To: Rotary motors in aircraft Message-id: MIME-version: 1.0 X-Mailer: Sun Java(tm) System Messenger Express 6.1 HotFix 0.20 (built Feb 27 2006) Content-type: text/html; charset=us-ascii Content-language: en Content-transfer-encoding: 7BIT Content-disposition: inline X-Accept-Language: en Priority: normal X-Proofpoint-Virus-Version: vendor=fsecure engine=2.50.10432:5.2.15,1.0.148,0.0.0000 definitions=2011-04-22_08:2011-04-22,2011-04-22,1970-01-01 signatures=0 X-Proofpoint-Spam-Details: rule=outbound_notspam policy=default score=0 spamscore=0 ipscore=0 suspectscore=2 phishscore=0 bulkscore=0 adultscore=0 classifier=spam adjust=0 reason=mlx engine=5.0.0-1012030000 definitions=main-1104220119 Ernest, I'm not looking to duplicate either completely. Rather having the details of what they made work and what would work better for the average builder is where I'm looking to go. Having all the cards on the table and the ability to pick and choose what we think is the best setup for everyone is as good as it gets in problem solving or product improvements.

Thanks also to Kelly for all the intel and pictures. I'll be in touch in regards to parts etc..Btw, Kelly where are you located?

Great to be starting down this road finally.. it's been a long time coming !

Jarrett Johnson
www.innovention-tech.com

Jarrett Johnson
www.innovention-tech.com

----- Original Message -----

From: Ernest Christley <echristley@att.net>

Date: Friday, April 22, 2011 10:23 am

Subject: [FlyRotary] Re: Mistral 'Like' Intake

> On 04/22/2011 12:01 PM, Kelly Troyer wrote:
> > Jarrett,
> > The main problem (from my eyeball engineering) will be
> integrating
> > the Renesis (or other) water-pump into a simplified
> > "Mistral" hsg without any interference with the Lycoming mount
> ring
> > and "Dyna-focal" engine mounts..........The only part of
> > the "Renesis" hsg that has to be duplicated is the water-pump
> hsg
> > portion (see photo) and provisions made for locating
> > the "Renesis" ignition sensor in the same relative position on a
> > redesigned "Mistral" hsg..............Much of the "Mistral"
> > open front can be eliminated (no need for the accessory drive
> section)
> > but retaining the removable front cover (which
> > doubles as a alternator mount point) would be a nice feature
> (but add
> > complication) as it allows access to the 13B front
> > thrust brg , gear stack and oil pump without pulling the engine
> (this
> > feature is not necessary if it is too costly).............The
> > relative positions of the water-pump and front oil seal from the
> > 13B/Renesis frt side hsg need to be maintained to allow
> > the use of the "Renesis" frt hub , pulley and ignition trigger
> wheel
> > and to maintain pulley/belt alignment.............
> >
>
> If you're going for this much of a redesign, start with a clean
> sheet
> and incorporate a generator into the mount. You would need four
> raised
> lands around the crank to mount the stator against the housing,
> and a
> splined adapter to mount the rotor to the crank. You could then
> move to
> an electric water pump, or mount the drive pulley on the outside
> of the
> rotor.
>
>