|
|
Don,
I am not qualified to comment on the prop, however, I would like to know if you ported out the Renesis or made any other core modifications of note?
I have a medium street port on my 2nd gen turbo block as performed by Mazdatrix (I built it, they ported it). Since folks here do not seem to post what modifications they made to their engines I do not know if such modifications are giving me or others the desired HP increase. Since My Velocity is rated to fly with the 160 hp Lyc 320 I figured the "out of the box" 160 hp of the 13b would be safe/good enough, but, I would much rather be closer to 200 hp. Also, it was mentioned that my straight 13b may strain under what may be the heaviest Velocity ever build <sigh>. So, is your Renesis a stock build or is it giving your current performance with performance porting.
During my preliminary research on the 13b it seemed the conventional wisdom (Leon in Oz for one) that 200 hp was very doable with porting and proper breathing...hopefully my Mistral intake, much better than anything I could create, will give me good intake breathing. While 160 hp is the minimum recommended by Velocity, Inc, 180 and 200hp seems to be a much better fit.
Maybe I am tearing it up right now with my porting and just don't know it...or, perhaps my turbo desires are well founded. Just don't know so I was wondering about yours, and others, internal breathing.
Oh, I finally ordered my wastegate. The Performance Turbo 46mm. $314.99 with flanges and several springs, from low to high pressure.
FWIW.
Thanks.
All the best,
Chris Barber
Houston, GSOT
________________________________________
From: Rotary motors in aircraft [flyrotary@lancaironline.net] on behalf of Don Wallker [drwalker@gbis.com]
Sent: Tuesday, March 23, 2010 11:26 PM
To: Rotary motors in aircraft
Subject: [FlyRotary] Turbo Planning
So here is where I am at so far. For those of you just tuning in, I am
flying a Renesis powered RV-8, with all of Tracy's stuff and a
Catto76/88 prop. Flys great, and I'm getting comfortable with it.
It's just not getting enough power. About 6080 static and 1450 ft/mn
climb at about 2200 rpm prop at 100 mph and that's at full throttle.
Max indicated at 8000ft, 54 degree day, 2440 on the prop and 205 oil and
200 degree water. So I need more cooling and more power. I'm going to
attack both at once and get it all done.
I'm roughly basing these changes on what Dave Leonard has done. He's
been through all this and has a fast powerful and dependable turbo set
up in a similar airplane. RV-6. And it runs cool! For more info and
pictures, check out Dave's website n4vy.rotaryroster.net Also a lot of
ideas from John, Scott, Chris, Steve etc.
Radiator: C&R 3"x22x20, mounted under the oil pan. A 1" inlet and
outlet with short runs to the new water manifold that Ed is making. I'm
hoping I wont' have to build up the cowl, just cut into it, but I doubt
it. I will also have to increase the exit area and am not sure how to
do that yet.
Oil cooler: Dave was using a Setrab, but they kept leaking. Tracy is
using a 30 row C&R cooler on his 3 rotor.PT# oc 238 30 an10, They also
make a 25 row that is about the same size as the setrab and should work
and fit nicely behind the right cheek and provide a nice short oil line run.
Throttle body: Probably a 75mm Mustang
Intercooler: Dave is using a stock 91 Rx-7 one and I will probably use
the same. Hey, it fits! There will almost certainly need to be some
modifications to the inlet and outlet. I have a Tig and a neighbor who
is a great welder. We just tack things there, as I don't have enough
power in the hanger for continuous welding.
Intake: I'm going to try and keep it totally on the left side of the
engine and will use the existing Rx-8 lower aluminum intake manifold.
I'll cut it down, grind it level and have a plate welded on top, with 4
holes going to the intake tubes and short velocity stacks welded on. On
top and around will be the intake manifold itself. Just an aluminum box
with a throttle body attached. I'm not sure just where yet. It depends
on how much room there is. Combustion air will flow into the cowl,
possibly from down by the radiator, or from a naca scoop on the side,
to the turbo compressor, through it to the inner cooler and through it
and back to the throttle body. Not sure where the injectors will go,
but I'll try to use the existing injector holes. May have to use the
Simple Digital injector mounts. Note, fire sleeve all fuel lines. It
solved half my vapor lock problems.
Turbo: will be mounted on the left side of the engine and a little back
from directly out from the exhaust. May be 3 to 4 inches. This should
give me room for the inner cooler and intake manifold. But I may not
have room for the fuel pumps and filters and they may have to go back
inside the cabin, by my feet. Not a bad idea. I'll use 321 ss and make
an equal length exhaust manifold with a waste gate port that will run to
the output side of the turbine. The exhaust out of the turbine will
bend down and out the back cowl exit to a muffler. I'm going to try the
new Burns all SS muffler that some of the rotary racers are using. They
use stainless steel scruble for the packing. Can't burn that out! and
it's 3 lbs and my existing Hushpower is 9. There will be a oil line
going to the turbo with a normally open solenoid on it and an exit line
out. It will be 5/8ths and run down and around the engine to the other
side where it will go through the side of the engine, like I have the
RD-c return line. I don't want to have to pull the engine out of the
mount, but that is the only way. If someone knows a better place to
run it back into, let me know. The turbo will be supported by more than
the exhaust. When the exhaust is finished, it will be sent for Jet Hot
coating. There will be a SS shroud around the turbo and the same for
the exhaust. I still don't know if I should use a wet or dry turbo
housing, but more on that in the next post.
Your thoughts, comments and questions are encouraged.
Don Walker
N113BR, 28 hours
--
Homepage: http://www.flyrotary.com/
Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
|
|