|
Group,
One other opinion on this subject............The condition of the rotor oil side seals and their
respective "O" rings probably is a factor (along with the amount of 2 cycle oil used per gal of
fuel) that determines how much 2 cycle oil ends up in the sump...........These seals essentially
scrape the sides of the rotors and if the seals are worn past maximum or the "O" rings are
heat hardened they will let more fuel mix oil past them into the sump............IMHO
--
Kelly Troyer
"Dyke Delta"_13B ROTARY Engine
"RWS"_RD1C/EC2/EM2
"Mistral"_Backplate/Oil Manifold
-------------- Original message from "Ed Anderson" <eanderson@carolina.rr.com>: --------------
> Yvon, I don't know the minimum, but I used to have the same problem. I
> would have to drain 1/2 cup of crankcase oil after about 10 hours of flight.
> So I started reducing the amount of 2 cycle oil. I have flow for the last
> three years mixing 3/4 oz of 2-cycle oil to one gallon (US) of fuel with no
> apparent ill effects on the engine and I am no longer accumulating 2 cycle
> oil in the oil pan.
>
> Ed Anderson
>
> Rv-6A N494BW Rotary Powered
>
> Matthews, NC
>
> eanderson@carolina.rr.com
>
> http://www.andersonee.com
>
> http://www.dmack.net/mazda/index.html
>
> http://www.flyrotary.com/
>
> http://members.cox.net/rogersda/rotary/configs.htm#N494BW
>
> http://www.rotaryaviation.com/Rotorhead%20Truth.htm
>
>
> -----Original Message-----
> From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On
> Behalf Of Yvon Cournoyer
> Sent: Friday, July 03, 2009 11:29 AM
> To: Rotary motors in aircraft
> Subject: [FlyRotary] INJECTION OIL IN FUEL
>
> My engine is a 1986 13B with 88 hrs since remanufacture.
> I fly a Zenair Zenith with a cogbelt PSRU and a Warp Drive 3-blades prop
> and this engine never runs above 5700 rpm
> When I installed this engine in my Zenith I removed the metering oil
> pump and have been using two stroke injection oil mixed in the
> automobile fuel ( 87 octane gasoline)
> At first I used a volume mix of 128:1 gas to oil and soon noticed an
> increase of engine lubricating oil volume in the oil pan
> I have gradually reduced the volume mix of gas to oil to 140:1 but there
> is still a slight increase of engine lubricating oil in the pan.
> Also a local mechanic has mentionned that the two stroke injection oil
> is degrading the 20W-50 engine oil.
> How much can I reduce the volume mix of gas to oil ?
> Please advise
> Yvon
>
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub:
> http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
> __________ Information from ESET NOD32 Antivirus, version of virus signature
> database 3267 (20080714) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>
>
>
> __________ Information from ESET NOD32 Antivirus, version of virus signature
> database 3267 (20080714) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>
>
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
|