Chris,
Why don't you share the rotary detractors concerns with us.  There seems to
be nothing easy about getting an alternative engine set up to fly.  It is
not a plug and play installation.  It is easy to get discouraged.  That has
happened to several folks on this list.  You will get there.  I hope you
don't give up.

Bill B

-----Original Message-----
From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On
Behalf Of Christopher Barber
Sent: Sunday, June 28, 2009 4:51 AM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: More progress, more questions....

Bill,

I think you are correct about the tach and the secondaries.  I had it do it
again today when I was running only the secondaries.  The rpm was about 2000
revolutions faster when I shut off the primaries.

Today was spent replacing the 20 awg with the 16 awg that is mentioned in
the manual.  I also cleaned up some other wire issues resulting from me
separating the coil/injector wires from the EC2/EM2 wires.

Ed,

Thanks, seems you nailed it when you mentioned my oxygen sensor not being
grounded properly causing the mixture bar to be erratic, now it is amazing
how sensitive it seems. You were correct about a gasket that may be
preventing a proper ground by the exhaust manifold, so I ran a wire clamped
the the sensor to the ground block.

I still feel progress is being made, but I still seemed to be plagued by
inconsistencies.  Tonight, I was tuning at lower settings and things seems
to be going as expected.  I decided to ramp up the power and when I did the
engine started sputtering and not developing power above about 3400 rmp.
Came back to idle and it smoothed out, added power and more stumbles.  Damn.
I shut it down, restarted and it had gone away.  I went to WOT and the power
came on amazingly up to about 6200 rpm...and it felt like it.  Since my
temps were doing ok, I  kept it at full power for about 20 seconds or so
when the rpm dropped about 400 rpm to 5800.  
I did nothing to cause the change.  I then started to fiddle with the
mixture but it did not make a difference in bringing the power back.  
Hmmmm? Shut down, restarted and it did the same thing. Hmmm? Hmmmm?

Also, twice I had the engine want to stall when I cut the primaries.  A shut
down and restart had it come back on line again.  Sigh, I cannot even count
how many times I have rechecked connections and wires.

I am having continued problems with my charging system, so I will try to
focus on this for now as it could be a base cause of some of these concerns.
Al, spotted my low volts and I was aware of it but focusing on other issues
until my EE buddy can come out.  What he will be able to detect and help
correct would likely take me weeks, if I ever found it....since I have not
as of yet.

Most of today was spent with mundane issues (like better wire runs)  and
folks stopping by the hangar.  Also, having to try to put in perspective a
very well educated engineering type from another list who emailed me and
trashed the rotary and the EC2, in what I believe a well meaning, but very,
very harsh manner.  I value the concern and knowledge however, he blamed my
problems on the rotary etc, while I have seen most my issues being something
that could have happened with what ever engine I was learning about.  It
shook me in its tone and message, even if I do not agree....however, since I
do not wish to have my head in the sand, I do not take a well educated
persons mindful opinion lightly.

As always guys, thanks for reading and  putting your minds together for the
common good.

All the best,

Chris


>

--
Homepage:  http://www.flyrotary.com/
Archive and UnSub:
http://mail.lancaironline.net:81/lists/flyrotary/List.html