X-Virus-Scanned: clean according to Sophos on Logan.com Return-Path: Received: from imo-m16.mx.aol.com ([64.12.138.206] verified) by logan.com (CommuniGate Pro SMTP 5.0.9) with ESMTP id 1142016 for flyrotary@lancaironline.net; Mon, 05 Jun 2006 19:52:34 -0400 Received-SPF: pass receiver=logan.com; client-ip=64.12.138.206; envelope-from=BMears9413@aol.com Received: from BMears9413@aol.com by imo-m16.mx.aol.com (mail_out_v38_r7.5.) id q.3fc.3a60e01 (16099) for ; Mon, 5 Jun 2006 19:51:48 -0400 (EDT) Received: from mblk-d46 (mblk-d46.mblk.aol.com [205.188.212.230]) by air-id11.mx.aol.com (v109.13) with ESMTP id MAILINID113-3ee34484c39419b; Mon, 05 Jun 2006 19:51:48 -0400 Date: Mon, 05 Jun 2006 19:51:48 -0400 Message-Id: <8C8571224F81456-A8C-828E@mblk-d46.sysops.aol.com> From: bmears9413@aol.com References: Received: from 65.182.71.8 by mblk-d46.sysops.aol.com (205.188.212.230) with HTTP (WebMailUI); Mon, 05 Jun 2006 19:51:48 -0400 X-MB-Message-Source: WebUI X-MB-Message-Type: User In-Reply-To: X-Mailer: AOL WebMail 17385 Subject: Re: [FlyRotary] Re: Shoe Goo Research, Was Re: Protecting splices Content-Type: multipart/alternative; boundary="--------MailBlocks_8C8571224F81456_A8C_876E_mblk-d46.sysops.aol.com" MIME-Version: 1.0 To: flyrotary@lancaironline.net X-AOL-IP: 205.188.212.230 X-Spam-Flag: NO ----------MailBlocks_8C8571224F81456_A8C_876E_mblk-d46.sysops.aol.com Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit As far as sealing elect wires ans stress relief, would hot glue do the trick? Bob Mears -----Original Message----- From: Bulent Aliev To: Rotary motors in aircraft Sent: Mon, 5 Jun 2006 19:36:33 -0400 Subject: [FlyRotary] Re: Shoe Goo Research, Was Re: Protecting splices >> > I tested rubber cement and shoe goo by placing a drop of each on pink > foam. I was looking for something that would glue the foam together > and dry fast. Rubber cement dissolved the foam right away. The shoe > goo didn't do much, but I should have looked later. After a few > minutes, the shoe goo dissolves the foam way too much to use it as a > glue, but not quite as much as the rubber cement did. > > I found this out today when I tried to glue another piece of foam to > the mold I'm making for my cooling plenum. I retested the drops of > shoe goo and rubber cement on another piece of foam but let them sit a > little longer. The rubber cement dissolved almost all the way thru a 1 > inch thick piece of foam. The shoe goo ate about 1/2 or 2/3 of the > way > thru, but left a film of shoe goo over the "pit". The shoe goo dollop > may have been smaller than the rubber cement dollop. > > So far I've successfully stuck the foam together with silicon bath tub > caulk and 5 minute epoxy. I also filled the voids with the > poly-urethane foam that comes from the hardware store in a spray can. > This stuff sticks to almost everything. BTY, shoe goo does not > dissolve > poly-urethane foam. > > Bob W. > > Bob, I have used 3M spray glue #77 from Home Depot on styrofoam. Works well without disoving it much. Buly -- Homepage: http://www.flyrotary.com/ Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/ ----------MailBlocks_8C8571224F81456_A8C_876E_mblk-d46.sysops.aol.com Content-Type: text/html; charset="us-ascii" Content-Transfer-Encoding: 7bit

As far as sealing elect wires ans stress relief, would hot glue do the trick?

Bob Mears

-----Original Message-----
From: Bulent Aliev <atlasyts@bellsouth.net>
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
Sent: Mon, 5 Jun 2006 19:36:33 -0400
Subject: [FlyRotary] Re: Shoe Goo Research, Was Re: Protecting splices

>>
> I tested rubber cement and shoe goo by placing a drop of each on pink
> foam. I was looking for something that would glue the foam together
> and dry fast. Rubber cement dissolved the foam right away. The shoe
> goo didn't do much, but I should have looked later. After a few
> minutes, the shoe goo dissolves the foam way too much to use it as a
> glue, but not quite as much as the rubber cement did.
>
> I found this out today when I tried to glue another piece of foam to
> the mold I'm making for my cooling plenum. I retested the drops of
> shoe goo and rubber cement on another piece of foam but let them sit a
> little longer. The rubber cement dissolved almost all the way thru a 1
> inch thick piece of foam. The shoe goo ate about 1/2 or 2/3 of the > way
> thru, but left a film of shoe goo over the "pit". The shoe goo dollop
> may have been smaller than the rubber cement dollop.
>
> So far I've successfully stuck the foam together with silicon bath tub
> caulk and 5 minute epoxy. I also filled the voids with the
> poly-urethane foam that comes from the hardware store in a spray can.
> This stuff sticks to almost everything. BTY, shoe goo does not > dissolve
> poly-urethane foam.
>
> Bob W.
>
>

Bob, I have used 3M spray glue #77 from Home Depot on styrofoam. Works well without disoving it much.
Buly

--
Homepage: http://www.flyrotary.com/
Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/

----------MailBlocks_8C8571224F81456_A8C_876E_mblk-d46.sysops.aol.com--