X-Virus-Scanned: clean according to Sophos on Logan.com Return-Path: Sender: To: lml@lancaironline.net Date: Tue, 22 Oct 2013 07:56:01 -0400 Message-ID: X-Original-Return-Path: Received: from carbinge.com ([69.5.27.218] verified) by logan.com (CommuniGate Pro SMTP 6.0.7) with SMTP id 6550006 for lml@lancaironline.net; Tue, 22 Oct 2013 01:05:53 -0400 Received-SPF: none receiver=logan.com; client-ip=69.5.27.218; envelope-from=jbarrett@carbinge.com Received: (qmail 29597 invoked from network); 22 Oct 2013 05:05:19 -0000 DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; h=X-Originating-IP:Reply-To:From:To:References:In-Reply-To:Subject:Date:Message-ID:MIME-Version:Content-Type:X-Mailer:Thread-Index:Content-Language; s=default; d=carbinge.com; b=XFd7KHSuiIWSCAAnwZX2CpQwpB+CiOoriqK98wtcYbdUxCmSuTJMzNaFsElRpOVUYMf09LBFmoOdBBUFA7e5XsNAjq7/zq7pHxwh+Db5vlXnBGMjFw+10xX9LmGFfQiRo7gBeabfdDnGkFrfZVT3K9sfUGXXJ8MG0pG/oP4I+xU=; X-Originating-IP: [208.53.115.208] Reply-To: From: "John Barrett" X-Original-To: "'Lancair Mailing List'" References: In-Reply-To: Subject: RE: [LML] Re: GAMIjector installation on TSIO 550 X-Original-Date: Mon, 21 Oct 2013 22:05:19 -0700 X-Original-Message-ID: <015a01cecee4$4e540e80$eafc2b80$@com> MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_015B_01CECEA9.A1F53680" X-Mailer: Microsoft Office Outlook 12.0 Thread-Index: Ac7OeqnG51aL4zKbRK2+wo9g+nJIjwAaQ/8g Content-Language: en-us This is a multi-part message in MIME format. ------=_NextPart_000_015B_01CECEA9.A1F53680 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Jay, =20 Check out the advice from several on the special socket tool you=92ll = need. They are on sale for about $50 to over $90. I turned down a =BC=94 = drive 7/16=94 socket at the socket end today and got five of the injectors changed. = #3 is a bitch because it is directly under the intake stack. #2 was difficult also and if I had cut a 45 degree bevel at the drive end of the socket, = it would be better. =20 =20 I am going to shorten a socket up tonight and weld a nut on top to get = out that last injector. =20 Best regards, =20 John =20 BTW, I have 1 GPH flow difference at peak so my results should be a = little more dramatic than yours. =20 =20 From: Lancair Mailing List [mailto:lml@lancaironline.net] On Behalf Of = Jay Phillips Sent: Monday, October 21, 2013 9:29 AM To: lml@lancaironline.net Subject: [LML] Re: GAMIjector installation on TSIO 550 =20 I also just purchased Gamijectors for my IV-P/TSIO-550. I collected = detailed info prior to the purchase. And they will be installed in the next week = or so. I=92ll collect post-installation data and submit my results. =20 Pre-installation, my GAMI lean test showed 0.7 gph difference between = first and last to lean. Not terrible, but it should be below 0.5 according to GAMI. Operating lean of peak I saw 65-70 dF difference between the = hottest and coldest CHTs. I=92d like that to be a lot closer. =20 Jay Phillips =20 From: Lancair Mailing List [mailto:lml@lancaironline.net] On Behalf Of William A. Hogarty Sent: Monday, October 21, 2013 8:46 AM To: Lancair Mailing List Subject: [LML] Re: GAMIjector installation on TSIO 550 =20 John: =20 Please post results after you replace your injectors. =20 Thanks, Bill Hogarty =20 On Mon, Oct 21, 2013 at 7:38 AM, Ron Laughlin = wrote: John, Order this socket that is custom made for the task: =20 Ron =20 On Mon, Oct 21, 2013 at 6:40 AM, John Barrett = wrote: Hello All, =20 I recently acquired a set of GAMIjectors for my TSIO 550 in N31VP. I am trying to install them and it appears I=92m going to have to remove the = intake stacks to be able to access the injectors. =20 =20 Is this correct or is there a trick or tool I don=92t know about? If I = do have to remove the intake pipes, do I need to replace the gaskets for = the pipes when they go back in? What is the torque for the three hold down = nuts on the intake pipes? =20 Thanks in advance. =20 Regards, =20 John Barrett, CEO Leading Edge Composites PO Box 428 Port Hadlock, WA 98339 =20 www.carbinge.com =20 =20 =20 ------=_NextPart_000_015B_01CECEA9.A1F53680 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable

Jay,

 

Check out the advice from several on the special socket tool = you’ll need.=A0 They are on sale for about $50 to over $90.=A0 I = turned down a =BC” drive 7/16” socket at the socket end = today and got five of the injectors changed.=A0 #3 is a bitch because it = is directly under the intake stack.=A0 #2 was difficult also and if I = had cut a 45 degree bevel at the drive end of the socket, it would be = better.=A0

 

I am going to shorten a socket up tonight and weld a nut on top to = get out that last injector.

 

Best regards,

 

John

 

BTW, I have 1 GPH flow difference at peak so my results should be a = little more dramatic than yours.

 

 

From:= = Lancair Mailing List [mailto:lml@lancaironline.net] On Behalf Of = Jay Phillips
Sent: Monday, October 21, 2013 9:29 = AM
To: lml@lancaironline.net
Subject: [LML] Re: = GAMIjector installation on TSIO 550

 

I also just purchased Gamijectors for my IV-P/TSIO-550. I collected = detailed info prior to the purchase. And they will be installed in the = next week or so. I’ll collect post-installation data and submit my = results.

 

Pre-installation, my GAMI lean test showed 0.7 gph difference between = first and last to lean. Not terrible, but it should be below 0.5 = according to GAMI. Operating lean of peak I saw 65-70 dF difference = between the hottest and coldest CHTs. I’d like that to be a lot = closer.

 

Jay Phillips

 

From:= = Lancair Mailing List [mailto:lml@lancaironline.net] = On Behalf Of William A. Hogarty
Sent: Monday, October = 21, 2013 8:46 AM
To: Lancair Mailing List
Subject: = [LML] Re: GAMIjector installation on TSIO 550

 

John:

 

Please post results after you replace your = injectors.

 

Thanks, Bill Hogarty

 

On Mon, Oct 21, 2013 at 7:38 AM, Ron Laughlin <ronlaughlin@gmail.com> = wrote:

John,

Order = this socket that is custom made for the = task:

 


Ron

 

On Mon, Oct 21, 2013 at 6:40 AM, John Barrett <jbarrett@carbinge.com> = wrote:

Hello = All,

 <= /o:p>

I recently = acquired a set of GAMIjectors for my TSIO 550 in N31VP.  I am = trying to install them and it appears I’m going to have to remove = the intake stacks to be able to access the injectors. =  

 <= /o:p>

Is this = correct or is there a trick or tool I don’t know about?  If I = do have to remove the intake pipes, do I need to replace the gaskets for = the pipes when they go back in?  What is the torque for the three = hold down nuts on the intake pipes?

 <= /o:p>

Thanks in = advance.

 <= /o:p>

Regards,

 <= /o:p>

John = Barrett, CEO

Leading = Edge Composites

PO Box = 428

Port = Hadlock, WA 98339

 <= /o:p>

www.carbinge.com

 <= /o:p>

 

 

------=_NextPart_000_015B_01CECEA9.A1F53680--