|
|
Using the stock ECU, there are no hot/cold start procedures. Engine always
starts on the first few turns no matter what. I have always shut down the
engine by killing the fuel pumps, with the advantages mentioned by Jim
below. Interestingly, I've never flooded the engine in my plane in more than
400 hours. My RX-7s have flooded numerous times.
On Tue, 09 Mar 2004 16:27:19 -0600, Jim Sower wrote
> I donno' about that. Lots of different procedures depending on
> if engine is hot or cold or flooded. At what temp do you switch
> from HOT start procedures to COLD start procedures, and who
> tells you when to use the FLOODED procedure? My guess is that
> the FLOODED procedure comes into play when some poor slob uses
> the COLD procedure when the engine is a little warmer than he
> thought it was.
>
> I have an IO-360 in my Velocity and I use the same procedure ALL
> the time - hot, cold, flooded (which it never gets) or
> whatever. That way I don't have to make a lot of judgment calls
> around the temperature and mood of the engine or the phase of
> the moon.. I just assume it's hot/flooded. Like:
> Left Mag ON (I have "combat switches", not a key)
> Throttle CRACKED (from last shutdown - 1000-1100 rpm)
> Mixture OFF
> Crank engine. When engine has cranked a couple of seconds:
> Mixture RICH and after a second or two:
> Boost Pump ON Right Mag ON
> Engine invariably starts at some point during the procedure.
> All I have to do is treat it as if its hot and flooded EVERY
> time. When it's not, it takes maybe 3 or 4 more seconds of
> cranking to start. That is a small price to pay for taking all
> the guesswork out of everything.
>
> Regarding "dripping injectors", I plan on shutting down my
> rotary by shutting down the fuel pump. If I do that, there is
> less/no pressure in the rail when the engine stops and the
> injectors have much less incentive to "drip".
>
> Just a theory --- Jim S.
>
> Mark Steitle wrote:
>
> > I'm forwarding a message from the Lancair list about hot
> > start techniques needed for certified a/c installations. I
> > was curious if there are similar issues for rotary
> > installations. I suspect not, but thought I would ask anyway.
> >
> > Mark S.
> >
> >> The IO-360 is also used on the Mooney M20E/F/J models and
> >> hot starts are always an issue, especially among the pilots
> >> that try and follow the owners' manual's recommendation of a
> >> flooded start when the engine is hot. While your exact
> >> setup is different than on a Mooney, the procedures may work
> >> for you. Following is an excerpt from a post to the Mooney
> >> Mailing list from a year or two ago. I follow the shutdown
> >> and hot start procedure every single time and it always
> >> works. Before I was taught this many years ago, I too was
> >> convinced that hot starts were somehow linked to the phase
> >> of the moon or something even more erratic like female
> >> moods. With this procedure, I am as confident about the
> >> engine starting as I am about democrats raising taxes.
> >>
> >> COLD START PROCEDURE
> >>
> >> Master Switch On
> >> Throttle, prop and mixture controls full forward
> >> Boost pump on for 5 seconds
> >> Mixture to idle cutoff
> >> Throttle reduce to the approximate position for a 1000-1100
> >> RPM idle speed
> >> Engage starter
> >> When engine fires, release starter key and firmly (but not
> >> rapidly) move mixture control to full rich
> >> After engine is running, lean mixture control out for smooth
> >> idle
> >>
> >> HOT START PROCEDURE
> >>
> >> Master Switch On
> >> DON T TOUCH THE THROTTLE, PROP OR MIXTURE CONTROLS. The
> >> throttle should be in the 1000-1100 RPM position from the
> >> previous shutdown, the mixture should be in the idle cutoff
> >> and the prop should be full forward.
> >> Engage the starter
> >> Expect about 15-20 blades before the engine fires
> >> When the engine fires, smoothly (not rapidly) move the
> >> mixture control to full rich
> >> After idling, lean the mixture for smooth operation on the
> >> ground and during taxi
> >>
> >> FLOODED ENGINE START PROCEDURE
> >>
> >> Master Switch On
> >> Throttle, prop and mixture full forward
> >> Boost pump on 3 seconds, then off
> >> Mixture to idle/cutoff
> >> Throttle full open
> >> Engage the starter
> >> Slowly pull the throttle back towards idle as the engine is
> >> turning over with the starter engaged
> >> When the throttle is reduced to about ½ to ¾ towards the
> >> idle position, the engine should fire after the throttle
> >> hits the position for the perfect fuel/air mixture for
> >> starting.
> >> When the engine fires, smoothly increase the mixture to full
> >> rich
> >> Bring the throttle back to the normal idle speed (1000-1100
> >> RPM)
> >> After idling awhile, lean the mixture for smooth operations
> >> on the ground and during taxi
> >>
> >> RECOMMENDED ENGINE SHUTDOWN PROCEDURE FOR THE MOONEY M20E
> >>
> >> Idle the engine at 1000-1100 RPM
> >> Pull the mixture control to idle/cutoff from this idle speed
> >>
> >> DO NOT TOUCH THE THROTTLE. Leave it at the setting it was at
> >> for the
> >> 1000-1100 RPM idle speed used for shut down
> >> Ignition switch to off after the engine spools down
> >> Master Switch Off
> >>
|
|