X-Virus-Scanned: clean according to Sophos on Logan.com Return-Path: Received: from [207.115.11.53] (HELO fmailhost01.isp.att.net) by logan.com (CommuniGate Pro SMTP 5.2.3) with ESMTP id 2936832 for flyrotary@lancaironline.net; Sat, 24 May 2008 10:24:50 -0400 Received-SPF: pass receiver=logan.com; client-ip=207.115.11.53; envelope-from=bbradburry@bellsouth.net Received: from desktop (adsl-146-124-244.mco.bellsouth.net[72.146.124.244]) by isp.att.net (frfwmhc03) with SMTP id <20080524142409H0300lib3ke>; Sat, 24 May 2008 14:24:09 +0000 X-Originating-IP: [72.146.124.244] From: "Bill Bradburry" To: "'Rotary motors in aircraft'" References: In-Reply-To: Subject: RE: [FlyRotary] Re: Fuel Filtering Problem Date: Sat, 24 May 2008 10:24:10 -0400 Message-ID: MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_0009_01C8BD88.4E678C30" X-Mailer: Microsoft Office Outlook 11 Thread-Index: Aci9k7OIG5nlsoRLT/WYbfZ0ypSQrwAE06Yw X-MimeOLE: Produced By Microsoft MimeOLE V6.0.6001.18000 This is a multi-part message in MIME format. ------=_NextPart_000_0009_01C8BD88.4E678C30 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable The pressure regulator is on the firewall just after the secondary fuel rail. Connected to the rail by about 2 feet of -6 SS braided hose. At the bottom of this msg, I tried to trace out the fuel system in order = of flow. The size is -8 from the Gascolator to the pumps, (about 1 foot), = then -6 the rest of the way to the regulator. Bob has a point about the size of the filter. The filter media on the = ones I have are only about 7/8 inch or so in diameter, so they could get = plugged rapidly if there was some component failure. I am not certain that I = would only want to go with one though after this has happened. I would have = to redesign the system, though. There is no room for them in the present layout. =20 Bill B=20 =20 _____ =20 From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On Behalf Of Mark Steitle Sent: Saturday, May 24, 2008 7:45 AM To: Rotary motors in aircraft Subject: [FlyRotary] Re: Fuel Filtering Problem Bill,=20 Where is the pressure regulator located in the system? (A = picture/sketch would sure be nice) Mark On Fri, May 23, 2008 at 11:26 PM, Bob White wrote: Hi Bill, When I first installed my system I had two of the small inline filters which I think were similar to the ones you are using. Somewhere along the way, Buly mentioned a different filter. It's about the same size as an oil filter. Summit Racing P/N PRM-81794. It will hold many times more contaminants than the small filters. I felt comfortable using one filter for both pumps. If you have the room, you might consider it. No new ideas on where the contamination is coming from. Bob W. On Fri, 23 May 2008 22:06:39 -0400 "Bill Bradburry" wrote: > Kelly, > > The only pressure that I have available is driven by the fuel = regulator. It > is set at 36 # at sea level pressure. It should maintain that = pressure when > the engine is running WOT. It would be less at idle. I think 30. = When I > turn the secondary pump on, the pressure goes up 2-3 lbs. > > Pressure on both sides of the filters would give an early warning of = this > problem, but I have not heard that anyone has installed that type of > instrumentation. > > One thing that has come of this problem is that I have realized that I have > to way to turn the primary pump off since it is on the same switch as = the > EC-2 power. I need to correct this as well. > > > > Bill B > > _____ > > From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] = On > Behalf Of Kelly Troyer > Sent: Friday, May 23, 2008 8:48 PM > To: Rotary motors in aircraft > Subject: [FlyRotary] Re: Fuel Filtering Problem > > Bill, > > What is the fuel pressure on the primary pump compared to the = secondary > > pump ??.........These are rotary vane pumps (I do not know the = composition > > of the vanes) and will gradually wear........They use the fuel to both cool > and > > lubricate their bearings and vanes.........If run dry for any reason = they > will self destruct very rapidly and could produce the black sludge you = are > seeing......... > > > > -- > Kelly Troyer > "Dyke Delta"_13B ROTARY Engine > "RWS"_RD1C/EC2/EM2 > "Mistral"_Backplate/Oil Manifold > > > > > > > -------------- Original message from "Bill Bradburry" > : -------------- > > I could use a little help on this problem. I apologize for the = length. > > > > My engine recently started to show signs of fuel starvation. Cutting = out > above about 3K rpm. It would just seem to go from 3K to idle. I was > running on my primary fuel pump, so I turned on the secondary and the engine > would start to run normally. (Not like gangbusters, but NORMALLY. My = max > static rpm has been about 52-5300 rpm and I have felt that it was not > getting enough fuel to run up to my goal of 6K static) > > > > I decided that I had a filter plugged, and fearing the gasohol that = they > are now selling all over Florida, I opened up my Gascolator. It was = ok. I > found a couple of wisps of white fibers. Could be fiberglass dust, = could be > spider webs, something like that. I don't think that I have had any > gasohol in the plane, but it is probably possible. But the Gascolator = was > fine. > > > > I then opened up the JEGS inline filter on the primary pump and the element > was covered with a black sludge. It seemed to be almost completely blocked. > This stuff looked like maybe it could have come from the inside of the = SS > braided hose. > > > > I checked the secondary pumps filter and it was fine. I have not used this > secondary pump except on rare occasions to check for pressure changes, > leaks, etc.. > > > > But for that matter, I have only run three 5 gal cans of gas in the = plane > totally. One 5 gal can in each wing, then another in the right side, = and I > am now pulling out of the left tank which has the fourth 5 gal in it. > > > > So, like I said, I at first thought that it was a rubber residue from = when I > installed the hose ends on the Aeroquip hoses because it sort of = looked like > that. Then as I drove home, I remembered that there was none of this stuff > in the Gascolator. (I think that some should have made it there as = there is > one -8 hose in front of the Gascolator) There is only about a foot of = -8 > hose in front of the fuel pumps after the Gascolator, so now I am = thinking > that maybe it came from the fuel pump. > > > > Is there anything inside the pump that could cause a black sludge if = it > started to crap out? What would I look for to check if the pump is = out or > going out. Has anyone else had any similar problem? I recently heard = a > squealing sound from the area of the pumps, but at the time I thought = that > it was bubbles going through the pump. I was close to empty on the = right > tank and thought that it was sucking air. I switched tanks and the = sound > went away. > > > > I have not yet checked my injectors. Two reasons: I have no idea of = how > to do it and would not know what to look for. Is the 40 micron screen fine > enough to keep anything from getting plugged up in the injectors? If = not, > what do I look for, and where? > > > > I would greatly appreciate some input as to your thoughts on this. = How > would you proceed? > > > > My fuel system goes: Finger strainer in tank, =BD inch aluminum line = to Andair > dual valve (switches both supply and return to same tank), Aeroquip -8 = SS > braided line, boost pump, Aeroquip -8 SS braided line, Andair = Gascolator, > Aeroquip -8 SS braided line about one foot to splitter to two fuel = pumps, > (these are the pumps that Tracy sells), each pump is followed by a = JEGS > billet in line fuel filter with a stainless 40 micron element. Then a > splitter to bring them back together to Aeroquip -6 SS braided line, primary > injector rail, Aeroquip -6 SS braided line, secondary injector rail, > Aeroquip -6 SS braided line, Aeromotive fuel pressure regulator, = Aeroquip -4 > SS braided line to the valve and back to the tank. The tanks are fiberglass > with ProSeal. This is a Lancair Legacy, Renesis engine. > > > > Thanks for the help. > > > > Bill B > > -- N93BD - Rotary Powered BD-4 - http://www.bob-white.com 3.8 Hours Total Time and holding Cables for your rotary installation - http://roblinstores.com/cables/ -- Homepage: http://www.flyrotary.com/ Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html =20 ------=_NextPart_000_0009_01C8BD88.4E678C30 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable

The pressure regulator is on the firewall just after the = secondary fuel rail.=A0 Connected to the rail by about 2 feet of -6 SS braided = hose.

At the bottom of this msg, I tried to trace out the fuel system = in order of flow.=A0 The size is -8 from the Gascolator to the pumps, = (about 1 foot), then -6 the rest of the way to the = regulator.

Bob has a point about the size of the filter.=A0 The filter = media on the ones I have are only about 7/8 inch or so in diameter, so they could get = plugged rapidly if there was some component failure.=A0 I am not certain that I = would only want to go with one though after this has happened.=A0 I would have = to redesign the system, though.=A0 There is no room for them in the present = layout.

 

Bill B 

 

From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On Behalf Of Mark Steitle
Sent: Saturday, May 24, = 2008 7:45 AM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: = Fuel Filtering Problem

Bill,

Where is the pressure regulator located in the system?  (A = picture/sketch would sure be nice)

Mark

On Fri, May 23, 2008 at 11:26 PM, Bob White <bob@bob-white.com> = wrote:

Hi Bill,

When I first installed my system I had two of the small inline = filters
which I think were similar to the ones you are using.  Somewhere = along
the way, Buly mentioned a different filter.  It's about the same = size
as an oil filter.  Summit Racing P/N PRM-81794.  It will hold many
times more contaminants than the small filters.  I felt = comfortable
using one filter for both pumps.  If you have the room, you = might
consider it.  No new ideas on where the contamination is coming = from.

Bob W.


On Fri, 23 May 2008 22:06:39 -0400

"Bill = Bradburry" <bbradburry@bellsouth.net>= wrote:

> Kelly,
>
> The only pressure that I have available is driven by the fuel = regulator.  It
> is set at 36 # at sea level pressure.  It should maintain that pressure when
> the engine is running WOT.  It would be less at idle.  I = think 30.  When I
> turn the secondary pump on, the pressure goes up 2-3 lbs.
>
> Pressure on both sides of the filters would give an early warning = of this
> problem, but I have not heard that anyone has installed that type = of
> instrumentation.
>
> One thing that has come of this problem is that I have realized = that I have
> to way to turn the primary pump off since it is on the same switch = as the
> EC-2 power.  I need to correct this as well.
>
>
>
> Bill B
>
>   _____
>
> From: Rotary motors in = aircraft [mailto:flyrotary@lancaironline.net] On
> Behalf Of Kelly Troyer
> Sent: Friday, May 23, 2008 8:48 PM
> To: Rotary motors in = aircraft
> Subject: [FlyRotary] Re: Fuel Filtering Problem
>
> Bill,
>
>    What is the fuel pressure on the primary pump compared = to the secondary
>
> pump ??.........These are rotary vane pumps (I do not know the = composition
>
> of the vanes) and will gradually wear........They use the fuel to = both cool
> and
>
> lubricate their bearings and vanes.........If run dry for any = reason they
> will self destruct very rapidly and could produce the black sludge = you are
> seeing.........
>
>
>
> --
> Kelly Troyer
> "Dyke Delta"_13B ROTARY Engine
> "RWS"_RD1C/EC2/EM2
> "Mistral"_Backplate/Oil Manifold
>
>
>
>
>
>
> -------------- Original message from "Bill Bradburry"
> <bbradburry@bellsouth.net>= : --------------

>
>  I could use a little help on this problem.  I apologize = for the length.
>
>
>
> My engine recently started to show signs of fuel starvation. = Cutting out
> above about 3K rpm.  It would just seem to go from 3K to idle.  I was
> running on my primary fuel pump, so I turned on the secondary and = the engine
> would start to run normally.  (Not like gangbusters, but = NORMALLY.  My max
> static rpm has been about 52-5300 rpm and I have felt that it was = not
> getting enough fuel to run up to my goal of 6K static)
>
>
>
> I decided that I had a filter plugged,  and fearing the = gasohol that they
> are now selling all over Florida, I opened up my Gascolator.  It was ok.  I
> found a couple of wisps of white fibers.  Could be fiberglass = dust, could be
> spider  webs, something like that.  I don't think that I = have had any
> gasohol in the plane, but it is probably possible.  But the Gascolator was
> fine.
>
>
>
> I then opened up the JEGS inline filter on the primary pump and the element
> was covered with a black sludge.  It seemed to be almost = completely blocked.
> This stuff looked like maybe it could have come from the inside of = the SS
> braided hose.
>
>
>
> I checked the secondary pumps filter and it was fine.  I have = not used this
> secondary pump except on rare occasions to check for pressure = changes,
> leaks, etc..
>
>
>
> But for that matter, I have only run three 5 gal cans of gas in the = plane
> totally.  One 5 gal can in each wing, then another in the = right side, and I
> am now pulling out of the left tank which has the fourth 5 gal in = it.
>
>
>
> So, like I said, I at first thought that it was a rubber residue = from when I
> installed the hose ends on the Aeroquip hoses because it sort of = looked like
> that.  Then as I drove home, I remembered that there was none = of this stuff
> in the Gascolator.  (I think that some should have made it = there as there is
> one -8 hose in front of the Gascolator)  There is only about a = foot of -8
> hose in front of the fuel pumps after the Gascolator, so now I am = thinking
> that maybe it came from the fuel pump.
>
>
>
> Is there anything inside the pump that could cause a black sludge = if it
> started to crap out?  What would I look for to check if the = pump is out or
> going out.  Has anyone else had any similar problem?  I = recently heard a
> squealing sound from the area of the pumps, but at the time I = thought that
> it was bubbles going through the pump.  I was close to empty = on the right
> tank and thought that it was sucking air.  I switched tanks = and the sound
> went away.
>
>
>
> I have not yet checked my injectors.  Two  reasons: =  I have no idea of how
> to do it and would not know what to look for.  Is the 40 = micron screen fine
> enough to keep anything from getting plugged up in the injectors? =  If not,
> what do I look for, and where?
>
>
>
> I would greatly appreciate some input as to your thoughts on this.  How
> would you proceed?
>
>
>
> My fuel system goes: Finger strainer in tank, =BD inch aluminum = line to Andair
> dual valve (switches both supply and return to same tank), Aeroquip = -8 SS
> braided line, boost pump, Aeroquip -8 SS braided line, Andair = Gascolator,
> Aeroquip -8 SS braided line about one foot to splitter to two fuel = pumps,
> (these are the pumps that Tracy sells), each pump is followed by a JEGS
> billet in line fuel filter with a stainless 40 micron element. =  Then a
> splitter to bring them back together to Aeroquip -6 SS braided = line, primary
> injector rail, Aeroquip -6 SS braided line, secondary injector = rail,
> Aeroquip -6 SS braided line, Aeromotive fuel pressure regulator, = Aeroquip -4
> SS braided line to the valve and back to the tank.  The tanks = are fiberglass
> with ProSeal.  This is a Lancair Legacy, Renesis engine.
>
>
>
> Thanks for the help.
>
>
>
> Bill B
>
>

--
N93BD - Rotary Powered BD-4 - http://www.bob-white.com
3.8 Hours Total Time and holding
Cables for your rotary installation - http://roblinstores.com/cables/

--
Homepage:  http://www.flyrotary.com/
Archive and UnSub:   http://mail.lancaironline.net:81/lists/flyrotary/List.h= tml

 

------=_NextPart_000_0009_01C8BD88.4E678C30--