The CHT data is not any good for diagnostic purposes in this
scenario. If you had fuel flow info as someone asked about, that would
be good. You didn't mention EGT. Got any? How about manifold
pressure? Not likely to have this on a Lyc, but mixture info
from O2 sensor would be even better. I won't leave home without it
after getting used to it.
Now for my mystery of the day. Was doing more tests on coil / alternator
cooling & wingtip testing today and got around to stall tests. I was
pleasantly surprised to find that my clean stall speed was down a full 5
MPH. That is HUGE, especially from such a simple mod.
Repeated the test multiple times, accelerated, power on, idle, 1 mph/ 10
second deceleration, the works. The change was real. Then I
tested 1/2 & full flap stall expecting that I would see the usual 4-5 mph
drop in stall speed. Absolutely no difference. Stall was the
same clean or dirty.
----- Original Message -----
Sent: Saturday, July 23, 2005 4:33
PM
Subject: [FlyRotary] Lycoming debugging
test - -HELP!
I realize that this isn't exactly the
right forum, but you guys seem to have excellent debugging skills. my
local RV group is totally worthless ("I find the carnauba wax doesn't show
fingerprints as much as the....")(except Mike!) the on-field mechanics
are sick of me coming by.
my O-320 RV-6A is
having RAG (rpm attention getter) problems. it runs fine until about
300' on take-off, then the rpm's drop to like 1700 (from 2200).
switching mags to electronic ignition(Rose) makes no difference.
mixture no diff. pulling the throttle it will seem to run fine at
1700rpm. I have 4 new cyls that I am attempting to break in.
ground run ups can only go like 2 minutes before CHT's exceed 400
degrees. I discovered I can get the rpm drop on the ground if I run it
a minute or so full power. cht's will typically approach 415 degrees
when the drop takes place. I don't know if the temp is significant or
not, it does seem that way. I have a brand new slick left mag.
rose checked the electronic ignition and could find nothing wrong, even put
it in an oven to test. I installed a new carb since the old one showed
signs of leakage (and I'm at whits end). no change. my fuel
pressure has been showing 8psi this last year, up from 6 psi when originally
installed.(no idea why) I installed a pressure regulator in-line which
works like a charm. I can dial whatever pressure I like. 2 psi
makes no difference. I bypassed the mechanical fuel pump and ran it
just on the facet electric. 2 psi, no difference. I discovered
that you can run the carb for maybe 30 secs with no fuel pressure while it
burns off the bowl gas. premier engines suggested induction leak making the
engine run lean. no leaks detected cold or hot engine. (pressurized
intake with vacuum, sprayed soapy water)
if the engine
didn't run right to start with then many explanations would hold. but
it runs fine for several minutes. it runs the same under mag or
electronic ignition both before and after the problem kicks in.
everyone really wants to blame the rose ignition, but I'm not seeing any
connection. with such a quick run-up my oil temp barely registers, so
I doubt parts are seizing. I have new mineral oil in it for breakin
right now. there is a bit of MMO in the fuel too I believe, left over
from a mechanics "what the hell" attempt from way back. my cyls are
all new, rebuilts, so no valve problems. I checked the push rod
lengths when I reinstalled them. the engine isn't missing when
the problems occurs, it simply won't run faster and it seems to prefer the
throttle pulled back to match the rpm it is putting out. I can't
figure out any more lean mixture scenarios to try. the new carb runs
just like the old one did. I recently replaced the mag harness with a
much newer, used one. I tested it and it was fine. the plugs are
all new, but again, no diff between mag and elec ignition. if I flip
the ignition to R and shut off the elect ig then the engine quits as would
be expected, no wiring problems.
fuel, spark, air,
timing, that's all there is. this damn lycoming lawn mower has me
stumped. my engine has been running fine up until this (hey, we all
have "cracked" cylinders, get out your microscope and look!). you guys
have any ideas?
----- Original