Return-Path: <lancair.list-request@olsusa.com>
Received: from pop3.olsusa.com ([63.150.212.2] verified)
  by logan.com (CommuniGate Pro SMTP 3.5b2)
  with ESMTP id 830817 for rob@logan.com; Tue, 17 Jul 2001 18:34:31 -0400
Received: from imo-d05.mx.aol.com ([205.188.157.37]) by pop3.olsusa.com
          (Post.Office MTA v3.5.3 release 223 ID# 0-71866U8000L800S0V35)
          with ESMTP id com for <lancair.list@olsusa.com>;
          Tue, 17 Jul 2001 17:52:45 -0400
Received: from RWolf99@aol.com
	by imo-d05.mx.aol.com (mail_out_v31.7.) id k.66.11a01a9c (4563)
	 for <lancair.list@olsusa.com>; Tue, 17 Jul 2001 18:01:51 -0400 (EDT)
From: RWolf99@aol.com
Message-ID: <66.11a01a9c.28860fcf@aol.com>
Date: Tue, 17 Jul 2001 18:01:51 EDT
Subject: Hysol Bonds
To: lancair.list@olsusa.com
MIME-Version: 1.0
Content-Type: text/plain; charset="US-ASCII"
Content-Transfer-Encoding: 7bit
X-Mailing-List: lancair.list@olsusa.com
Reply-To: lancair.list@olsusa.com

          <<<<<<<<<<<<<<<<--->>>>>>>>>>>>>>>>
          <<  Lancair Builders' Mail List  >>
          <<<<<<<<<<<<<<<<--->>>>>>>>>>>>>>>> 
>>
I just closed my wings last week at Aircrafters Builder Support Center in 
Watsonville CA.  I would like to extend my thanks to the guys up there, and 
pass on something I learned about the Hysol bonds that we use to close out 
wings, tails, stub wing skins, yada yada yada.

I was ably assisted by Harold Bunyi, an Aircrafters employee who has worked 
for ten years at both the Lancair facility in the Philippines and at the 
Redmond facility.  Harold tells me that he has assisted in the building of 
close to 60 Lancairs, so I listened to him pretty closely.  (I also had the 
opportunity to see his impeccable workmanship on other airplanes there at 
Aircrafters, and was fortunate enough to have him glass in my aileron transit 
tubes.  I'm sure they won't leak...)  He also has a degree in aeronautics, 
and is a pretty nice guy, too.

My early 320 FB manual (circa 1993) calls for smearing on pure hysol, and a 
1998 amendment pertaining to the horizontal tail calls for pure hysol 
augmented by a hysol + flocked cotton mixture.  For the record, I am using 
the term "flocked cotton" rather than "flox", since "flox" implies to me an 
epoxy + flocked cotton mixture rather than just the cotton by itself.

Harold had me do it this way, and says that this is how it's done now at the 
various locations which form the international Lancair mega-conglomerate....

First, you mix up some hysol.  Smear it onto the bonding surfaces on both 
sides of the joint (i.e. both the capstrip and the skin).  Then, scrape it 
off, leaving only a very thin layer.  The objective here is to wet out the 
surface with hysol, but not put enough on to do any real bonding.  If the 
surface looks wet, that's good enough.  If it looks gray, you probably have 
too much hysol.  Harold uses a metal paint scraper for this but I used a 
plastic Bondo scraper.  It doesn't really matter, but a tongue depressor 
won't scrape off enough.

Since you put the scraped off hysol back in your cup, you now have almost as 
much as when you started.  Mix in flocked cotton until it's too thick to run. 
 The 1998 supplement to my manual says "like peanut butter" but I'd have to 
say it's almost but not quite that thick.  Perhaps like warm peanut butter 
that's been stirred up a little.  (Oh ... it should go without saying that 
we're talking about smooth peanut butter -- not the chunky stuff....)

Put the thickened hysol on the capstrip.  Build a little triangle-shaped 
ridge along the length of the capstrip.  You can use a tongue depressor for 
this.  The hysol + flocked cotton mixture can be zero thickness at the edge 
building linearly to 3/16 inch thick in the center.  (Just run the tongue 
depressor along the edge, tilted so that it's 3/16 inch above the capstrip in 
the center.)

Put the skin on and weight it down with sandbags, shotbags, dried cow chips, 
or whatever you're using.  You will notice that there are no heinous hysol 
drips, since the flocked cotton keeps it from running.  You can wipe off the 
squeeze-out on the outside, but the stuff on the inside will stay in a nice 
little bead along the junctions.  However, there may be a small glob at the 
corners, where squeeze-out comes from two directions at once.

When we closed out the wings, I briefly removed the sandbags from the area 
around the aileron bellcrank access panel (leaving the bags on the, er, 
leading and trailing edges) and  reached in to remove the squeeze-out with a 
plastic scraper.  When I looked into the open fuel cap with a flashlight, I 
saw a nice smooth bead of hysol -- no drips at all.

By the way, it takes a complete 1-quart kit of hysol to close out each 320 
wing.  It takes most of a 1-quart kit to close out two stub wing skins.

- Rob Wolf

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
LML website:   http://www.olsusa.com/mkaye/maillist.html
LML Builders' Bookstore:   http://www.buildersbooks.com/lancair

Please send your photos and drawings to marvkaye@olsusa.com.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>