On 21 November 2020 at 12:51:42, Stephen Izett stephen.izett@gmail.com (flyrotary@lancaironline.net) wrote:

Hi Bruce

If I were starting again I would develop a belly mounted system something like Russell Sherwood dis in his Glasair IRG
Cheers

Steve

> On 21 Nov 2020, at 8:59 am, Bruce Cosgrove bcosgrove@mac.com <flyrotary@lancaironline.net> wrote:
>
> Hi Steve, Charlie, Matt, Roy and others
> I am in the process making up a cooling system for a Tango 2 and was also planning to use the wedge shaped diffuser design, however the information that I have been reading from the homebuilt airplanes site discussing alternate approaches with less drag and improved efficiency? has me re thinking my design towards a belly mounted radiator. The comments under the heading Successful Auto Conversion Trials, Tribulations and Tips, I found particularly interesting - in particular input from Russell and RJ6ejGUY who both have devised systems that are working well for them Belly radiators may not be everyones idea of how to proceed but I like the idea of relatively unimpeded air flow and freeing up space in the cowling. any feedback would be much appreciated.
>
> Bruce
>
> On 21 November 2020 at 10:00:57, Stephen Izett stephen.izett@gmail.com (flyrotary@lancaironline.net) wrote:
>
>> Nice work Charlie.
>>
>> Steve
>>
>> > On 21 Nov 2020, at 6:50 am, Charlie England ceengland7@gmail.com <flyrotary@lancaironline.net> wrote:
>> >
>> > My (untested in combat) version for my radiator looks similar, but because the inlet is offset, I had to use a turning vane to get flow into the lower front of the core. The outside doesn't give a good idea on how 'tight' the inner surface is. I had to use expanding foam to fill the inside, then re-shape, then glass over the foam. As I said, the back 1/4-1/3 of the diffuser tapers tightly to almost touch the core at the back.
>> >
>> > After observing both rotary and piston installations that work, I'm beginning to think that turning vanes may be the 'good enough' vs fighting for perfection in diffuser shape. My oil cooler core has a much more elaborate vane setup, driven by the very short duct length and even greater offset to the bottom edge of the core.
>> >
>> > Charlie
>> >
>> >
>> > On 11/20/2020 4:22 PM, Stephen Izett stephen.izett@gmail.com wrote:
>> >> Hi Roy
>> >>
>> >> Here is a photo of our Mocal 44 row oil cooler with diffuser. A K&M Streamline into a wedge.
>> >> Not sure of the dimensions of hand. The Mocal web site will have specs so you could get a rough idea of size.
>> >> I tested this one recently with a leaf blower approximating 100 knot air flow and in that test it was very even.
>> >>
>> >> Having said that, I tested our water radiator wedge diffuser when I built it years ago and had it reasonably even
>> >> measuring pressures across the exit face, but now instrumenting it in flight its flow is vastly uneven.
>> >>
>> >> I have found that the flow is dependant not only on getting the diffuser shape right according to the various papers (eg. K&W, London, Oblique Flow Diffusers - Streamline )
>> >> But importantly the environment it ends up in. The papers share data for ideal conditions with for example unobstructed exit air paths.
>> >> My thoughts now are that this has a significant impact on the performance and therefore the advantage of instrumenting in flight and reshaping for actual conditions.
>> >>
>> >> The data I collected yesterday of our H2O diffuser reveals that the air flow in various points across the face are very different.
>> >> Simplified, if I average the pressures at the five points I measured, then comparatively the back is up 20%, the centre up 25% and the front down 60% from that average figure.
>> >> I’m figuring a 20% difference is probably OK, but my front to back/middle difference of ~80% down in the front top of that radiator may hold significant room for improvement.
>> >> Further, my data suggests that as IAS rises those differences are amplified.
>> >> So I am now targeting the modifications for our worst case conditions of WOT sea level ~200hp and initial climb numbers of 115KIAS.
>> >>
>> >> Cheers.
>> >>
>> >> Steve Izett
>> >>
>> >>
>> >>
>> >>> On 21 Nov 2020, at 3:37 am, ROY GLENN rglenn14@sbcglobal.net <flyrotary@lancaironline.net> wrote:
>> >>>
>> >>> Could some ne post a photo of their wedge shape and dimensions.
>> >>> Thanks Roy
>> >>>
>> >>> --
>> >>> Homepage: http://www.flyrotary.com/
>> >>> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>> >>
>> >
>> >
>> >
>> >
>> > This email has been checked for viruses by Avast antivirus software.
>> > www.avast.com
>> >
>> >
>> > <rad duct1.JPG>--
>> > Homepage: http://www.flyrotary.com/
>> > Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>>
>>
>> --
>> Homepage: http://www.flyrotary.com/
>> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
> --
> Homepage:
> http://www.flyrotary.com/
>
> Archive and UnSub:
> http://mail.lancaironline.net:81/lists/flyrotary/List.html


--
Homepage: http://www.flyrotary.com/
Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html