Well, the MAP table was ok. The problem
was my high pressure fuel filter on the primary fuel pump. There were a lot of
black particles in the filter that had it blocked. The secondary filter was
clean but had only been run for a few minutes. This is the second time I found
black material in this filter. The first time was about 40 gallons ago. This
previous material was somewhat gooey and I thought that it may have come from
not properly cleaning my hoses out after I made them. This time the material looked
like tiny black particles. I don’t think they came from the hoses, but
if not, they must have come from the pump itself.
My fuel system is ..from the wing tanks: a
finger strainer in the outlet of the tank, then to a fuel selector valve, then
thru a boost pump, then to a Gascolator, then to either of primary or secondary
fuel pump, then a filter after each pump, then fuel rail, then fuel pressure
regulator, then excess fuel returns thru the selector valve to the tank I am
using from.
I haven’t yet checked my finger
strainers because they are a bitch to get to, but my Gascolator did not have
any of the black particles in it. It had a small amount of white fuzz that is
probably fiberglass dust from my fuel tanks in it. This leaves me a section of
-8 hose about 14 inches long or the fuel pump to be the source of the black
particles. Oh yeah, the finger strainers and the Gascolator are both able to
move fuel. I emptied both tanks of about 15 gal of fuel so that I could try
and check the finger strainers. The boost pump filled a 5 gal can in 2 or 3
minutes pumping thru the strainers and Gascolator. My fuel lines up to the FI
pumps are all either ½ inch or -8 in size. After the FI pumps the fuel lines
go to -6 to the regulator and -4 to return to the tanks.
Is anyone else seeing this kind of material
in their filters?
Also, since this occurred with about a
tank of gas since I last cleaned the filters, I am concerned about the capacity
of the fuel filters I am using. I am using Summit filters like the one here.
http://www.summitracing.com/parts/SUM-230105/
This filter has a small screen that is
about ¾ inch in diameter and is 40 microns, so when it gets very little
contamination, it plugs. I am thinking it would be fine for a drag car, but
not for hours of flight unless your system was so clean you didn’t need
it in the first place.
I originally had one filter in the system,
but became concerned and added another one. Now I am wondering if I should go
to the type of filter that looks like an oil filter and if I do, would one be sufficient
or should I try and put in two filters of that type. I have very little space
to add this type of filter and I don’t know if it would even be possible
to add two of them. I would really appreciate any input you guys could give
and possibly some pics of your installation if you are using the oil filter
type. Do these type have the capacity to flow fuel when they get contaminated
or will they block like these small in line filters?
Fuel starvation is a major cause of
experimental plane crashes and I am close enough to be thinking of flying.
:>) Hep me! Hep me!
Bill B
From: Rotary motors in aircraft
[mailto:flyrotary@lancaironline.net] On
Behalf Of Bill Bradburry
Sent: Sunday, January 16, 2011
5:24 PM
To: Rotary
motors in aircraft
Subject: [FlyRotary] Re: Apex
seals and MAP table corruption?
I may be taking it back what I said about
the MAP table. During my runup today, I noticed that the fuel pressure
was dropping. At full WOT, the pressure dropped to below 20 psi. I
engaged the secondary fuel pump and the pressure came back to the 40 lb range.
It appears that my fuel filter after the primary pump may be partially
clogged. I will clean them tomorrow and let you know what I find.
Bill B