Mailing List flyrotary@lancaironline.net Message #53580
From: Jeff Whaley <jwhaley@datacast.com>
Subject: Start and Pre-Flight Check lists
Date: Thu, 13 Jan 2011 07:56:16 -0800
To: 'Rotary motors in aircraft' <flyrotary@lancaironline.net>

Here¡¯s mine Bill ¡¦  Jeff

 

2.2          Engine Start

 

1.       Select FUEL ON (Push).

2.       Select MASTER and ALTERNATOR switches ON.

3.       Check VOLTMETER, if not ¡°in the green¡± do not proceed.                             Charge battery until voltmeter indication ©ø 13 Volts.

4.       Turn IGNITION key to ON, one notch to the right.

5.       Turn FUEL PUMP 1 ON, switch UP.

6.       Set EMS controller to Mode 0.

7.       Depress Store button 3-4 times to prime the engine.

8.       Set INJECTORS primary and secondary ON.

9.       Set throttle to closed position.

10.    Activate BRAKES, left and right.

11.    Check visual clearance and give audible warning.

12.    Engage starter, start switch up until engine starts.

13.    Check alternator, no-charge light is OFF

14.    Check oil pressure >60 PSI.

 

2.3          Pre-flight / Takeoff

 

1.       Connect SEATBELTS, lap and shoulder harnesses.

2.       Advance THROTTLE to set engine for 2400 RPM.

3.       Check/set FUEL PUMPS 1-ON/2-OFF; 2-ON/1-OFF; BOTH-ON.

4.       Warm engine until WATER temp is indicating ¡Ã 130 F.

5.       Check both ignition CONTROLLERs                                                           toggle switch A to B - Engine must operate on A&B or no take-off.                  B Controller: perform ignition coil check; note slight rpm drop.                              A Controller: return toggle switch back to A for take-off.

6.       Check MIXTURE knob function; set to Take-Off position.

7.       Check STAGING; advance rpm up through staging point and back down.

8.       Check inJECTORS: Primary-Only, Secondary-Only; BOTH.

 

From:

"Bill Bradburry" <bbradburry@bellsouth.net>

Subject:

RE: [FlyRotary] Re: Secondary injector idle was: [FlyRotary] Apex seals and MAP table corruption?

Date:

Thu, 13 Jan 2011 08:51:55 -0500

To:

"'Rotary motors in aircraft'" <flyrotary@lancaironline.net>

Message Header

Undecoded Message

My injectors are all the same size.  When I disable the secondary, I think it works as it should.  It is when I disable the primary that I am concerned about.  I haven¡¯t tried enriching the mixture as Ed suggested.  I will try that next time I run the engine to see if that is a factor.

What is the best/most popular engine run up check to do with our rotary engines before take off?  Does anybody have a check list that they would like to share??

 

Bill B

 



__________ Information from ESET NOD32 Antivirus, version of virus signature database 5784 (20110113) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com

This message, and the documents attached hereto, is intended only for the addressee and may contain privileged or confidential information. Any unauthorized disclosure is strictly prohibited. If you have received this message in error, please notify us immediately so that we may correct our internal records. Please then delete the original message. Thank you.
Image
image001.gif
Image
image002.gif
Subscribe (FEED) Subscribe (DIGEST) Subscribe (INDEX) Unsubscribe Mail to Listmaster