Hi Thomas,

See reply to Bob.  The pushers are definitely more work with those long
cable runs.  My work area isn't long enough.

Bob W.

On Mon, 30 Oct 2006 15:52:24 -0800
"Thomas Phy" <thomphy@msn.com> wrote:

> Me to. The RV-? crowd should be a no brainier.
> TP
> RV-7
> ----- Original Message -----
> From: "Bob Tilley" <btilley@mchsi.com>
> To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
> Sent: Monday, October 30, 2006 3:11 PM
> Subject: [FlyRotary] Re: Prewired EC2 Cables
>
>
> > Bob,
> >
> > I would like to get a wiring harness!  Tracy's EC2, LS1 coils, long  
> > wiring length. What other info do you need? I'm installing it in a  
> > Cozy MK IV.
> >
> > Bob Tilley
> > 802 Beechwood Dr
> > Albany, Ga 31721
> >
> >
> > On May 26, 2005, at 12:27 AM, Bob White wrote:
> >
> > > I'm contemplating offering prewired cables for Tracy's EC2.  I've been
> > > in the electronics field for over 40 years so soldering and cabling  
> > > are
> > > easy for me.
> > >
> > > I would prewire the 15 and 37 pin connectors to your specified length.
> > > Other wires would be long enough to be cut off and terminated by you.
> > > Wires would be tefzel (M22759/16) or better and each wire would be
> > > clearly marked.  Everything would be done to the specs in Tracy's
> > > manual.
> > >
> > > Using my installation as a reference, I would make the unterminated
> > > wires that go under the insturment panel 5 feet long and those  
> > > going to
> > > the engine compartment 10 feet long.  Length from the 15 pin
> > > connector to the 37 pin connector is 36 inches.  Based on that, the  
> > > cost
> > > would be $95 but this would be adjusted for different lenght
> > > requirements. These lengths should leave enough wire for most
> > > installations.
> > >
> > > Also, for the canard community, I would be willing to cable  
> > > anything up
> > > to your specifications, but because of the long runs and  
> > > sensitivity to
> > > noise I wouldn't want to gurantee sucess in using the cable.
> > >
> > > Is there any interest in such a service?
> > >
> > > Bob White
> > >
> > > --
> > > http://www.bob-white.com
> > > N93BD - Rotary Powered BD-4 (real soon)
> > >
> > >>>  Homepage:  http://www.flyrotary.com/
> > >>>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
> > >
> >
> >
> > --
> > Homepage:  http://www.flyrotary.com/
> > Archive and UnSub:   http://mail.lancaironline.net/lists/flyrotary/
> >
>
> --
> Homepage:  http://www.flyrotary.com/
> Archive and UnSub:   http://mail.lancaironline.net/lists/flyrotary/


--
N93BD - Rotary Powered BD-4 - http://www.bob-white.com
First engine start 1/7/06 - Special Airworthiness Certificate 10/1/06
Cables for your rotary installation - http://www.roblinphoto.com/shop/